Effects of gas sparging and mechanical mixing on sonochemical oxidation activity

The effects of air sparging (0–16 L min⁻¹) and mechanical mixing (0–400 rpm) on enhancing the sonochemical degradation of rhodamine B (RhB) was investigated using a 28 kHz sonoreactor. The degradation of RhB followed pseudo first-order kinetics, where sparging or mixing induced a large sonochemical enhancement. The kinetic constant varied in three stages (gradually increased → increased exponentially → decreased slightly) as the rate of sparging or mixing increased, where the stages were similar for both processes. The highest sonochemical activity was obtained with sparging at 8 L min⁻¹ or mixing at 200 rpm, where the standing wave field was significantly deformed by sparging and mixing, respectively. The cavitational oxidation activity was concentrated at the bottom of the sonicator when higher sparging or mixing rates were employed. Therefore, the large enhancement in the sonochemical oxidation was attributed mainly to the direct disturbance of the ultrasound transmission and the resulting change in the cavitation-active zone in this study. The effect of the position of air sparging and mixing was investigated. The indirect inhibition of the ultrasound transmission resulted in less enhancement of the sonochemical activity. Moreover, the effect of various sparging gases including air, N₂, O₂, Ar, CO₂, and an Ar/O₂ (8:2) mixture was compared, where all gases except CO₂ induced an enhancement in the sonochemical activity, irrespective of the concentration of dissolved oxygen. The highest activity was obtained with the Ar/O₂ (8:2) mixture. Therefore, it was revealed that the sonochemical oxidation activity could be further enhanced by applying gas sparging using the optimal gas.     

The role of the bubble–bubble interaction on radial pulsations of bubbles

Using a model that with or without considering the interaction between bubbles through the radiated pressure waves, numerical simulations of cavitation bubbles have been performed in order to study the effect of the bubble–bubble interaction on radial pulsations of bubbles. Comparing the results obtained by with or without considering the bubble–bubble interaction, it is suggested that the suppression or enlargement property of expansion ratios of bubbles due to the bubble–bubble interaction largely depends on the ultrasound parameters, the ambient bubble radii, the distances between bubbles and the number of bubbles (in multi-bubble environment, the last two aspects can be expressed using the coupling strength). The frequency response curve of expansion ratio decreases and shifts to left due to the bubble–bubble interaction and the larger the coupling strength is, the more the left-shifting is.     

Evolution of helium bubbles in nickel-based alloy by post-implantation annealing

Nickel-based alloys have been considered as candidate structural materials used in generation IV nuclear reactors serving at high temperatures. In the present study, alloy 617 was irradiated with 180-keV helium ions to a fluence of 3.6×10¹⁷ ions/cm² at room temperature. Throughout the cross-section transmission electron microscopy (TEM) image, numerous over-pressurized helium bubbles in spherical shape are observed with the actual concentration profile a little deeper than the SRIM predicted result. Post-implantation annealing was conducted at 700 ℃ for 2 h to investigate the bubble evolution. The long-range migration of helium bubbles occurred during the annealing process, which makes the bubbles of the peak region transform into a faceted shape as well. Then the coarsening mechanism of helium bubbles at different depths is discussed and related to the migration and coalescence (MC) mechanism. With the diffusion of nickel atoms slowed down by the alloy elements, the migration and coalescence of bubbles are suppressed in alloy 617, leading to a better helium irradiation resistance.     

气泡在超声场中绕圈运动的高速摄影及其图像分析

借助高速摄影和图像分析技术对首次发现的附壁气泡的绕圈现象进行了实验研究,重点研究游移气泡的运动轨迹、附壁气泡的布阵过程、气泡的来源以及气泡的振动细节.研究发现游移绕圈气泡的运动轨迹呈现出不稳定、不规则、不光滑的特点.阵列气泡源于游移气泡,而游移气泡变成阵列气泡的方式主要是通过合并增大体积,从而减小所受的Bjerknes力,降低活性的方式实现的.游移气泡源于ALF(acoustic lichtenberg figure)空化云中大量空泡的合并,使以径向振动为主的空泡逐渐过渡到以表面波动为主的气泡.阵列气泡在Bjerknes力的作用下呈现出规则的表面波动,而体积更小受力更大的游移空泡的表面完全失稳,呈现极不规则的形貌,并对附近阵列气泡的表面波动产生影响.阵列气泡呈现出十分规则的排布,相邻阵列气泡之间的振动相位是相反的,表现为相互排斥.     

Acoustics of a Bubbly Liquid with a Weak Chemical Reaction in the Gaseous Phase

The influence of the composition and thermophysical properties of gas-liquid bubbly systems with a dissociating component in the gaseous phase on the laws of small-disturbance propagation and attenuation is investigated. It is found that the reacting gas component in the bubbles significantly affects the sonic-wave attenuation coefficient in the bubbly liquid. This follows from the fact that when a gas bubble is compressed isothermally, a recombination reaction occurs which prevents pressure growth in the bubble.Small-disturbance propagation in bubbly liquids was investigated in a number of publications discussed in review [1]. The acoustics of a bubbly liquid with a gas phase containing active admixtures are of both methodical and practical interest. The dynamics of such multicomponent bubbles were investigated in [2].     

气泡振动的非线性耦合模型

我们推广了Longuet-Higgins关于各向同性气泡的非各向同性模式激发的二阶理论。着重注意“呼吸”模式和“变形”模式之间的相互作用,两个模式之间的能量交换足够强,以致于两个模式有同量级的振幅。文中指出:模式耦合的方程组类似于其他物理领域(如非线性光学、水波)所研究的方程组,并讨论了二种特解,考虑了平衡点及其稳定性。     

Formation and Amplification of Shock Waves in a Bubble “Cord”

The structure and dynamics of the wave field generated by a bubble system in the form of an axial bubble cylinder (cord) excited by a plane shock wave propagating along the axis in an axisymmetric shock tube are numerically examined. It is shown that consecutive excitation of oscillations of the bubble zone results in formation of a quasi-steady shock wave in the cord and in the ambient liquid. Results of the numerical analysis of the maximum amplitude of the resulting wave as a function of problems parameters are described.__________Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 46, No. 5, pp. 46–52, September–October, 2005.     

Water cavitation of hydrogels

Using the cavitation rheology (CR) technique developed in our labs, we show that fluids with negligible interfacial tensions with a surrounding material can be used to induce an elastic, cavitation instability in that material. We do this by changing the cavitation media from air, which was demonstrated to induce cavitation at the tip of a syringe needle in previous studies, to water, which has a negligible surface tension with the surrounding poly(vinyl alcohol) hydrogel material. In this case, the critical pressure in which this instability occurs can be directly related to the elastic modulus of the surrounding network and is shown to be nearly independent of length scale. This independence of size scale has important implications in the use of CR for the characterization of mechanical properties from molecular to macroscopic length scales. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1423–1427, 2010     

Study on the bubble transport mechanism in an acoustic standing wave field

The use of bubbles in applications such as surface chemistry, drug delivery, and ultrasonic cleaning etc. has been enormously popular in the past two decades. It has been recognized that acoustically-driven bubbles can be used to disturb the flow field near a boundary in order to accelerate physical or chemical reactions on the surface. The interactions between bubbles and a surface have been studied experimentally and analytically. However, most of the investigations focused on violently oscillating bubbles (also known as cavitation bubble), less attention has been given to understand the interactions between moderately oscillating bubbles and a boundary. Moreover, cavitation bubbles were normally generated in situ by a high intensity laser beam, little experimental work has been carried out to study the translational trajectory of a moderately oscillating bubble in an acoustic field and subsequent interactions with the surface. This paper describes the design of an ultrasonic test cell and explores the mechanism of bubble manipulation within the test cell. The test cell consists of a transducer, a liquid medium and a glass backing plate. The acoustic field within the multi-layered stack was designed in such a way that it was effectively one dimensional. This was then successfully simulated by a one dimensional network model. The model can accurately predict the impedance of the test cell as well as the mode shape (distribution of particle velocity and stress/pressure field) within the whole assembly. The mode shape of the stack was designed so that bubbles can be pushed from their injection point onto a backing glass plate. Bubble radial oscillation was simulated by a modified Keller–Miksis equation and bubble translational motion was derived from an equation obtained by applying Newton’s second law to a bubble in a liquid medium. Results indicated that the bubble trajectory depends on the acoustic pressure amplitude and initial bubble size: an increase of pressure amplitude or a decrease of bubble size forces bubbles larger than their resonant size to arrive at the target plate at lower heights, while the trajectories of smaller bubbles are less influenced by these factors. The test cell is also suitable for testing the effects of drag force on the bubble motion and for studying the bubble behavior near a surface.